TEKNİK TEDARİK VE MÜHENDİSLİK

Raziol Ürünleri

Raziol ürün kodları, teknik tedarik ve teklif süreçleri için Teknoais ile iletişime geçin.

ENDÜSTRİYEL ÜRÜN VE TEKNİK TEDARİK

Raziol ürünleri için teknik seçim

Raziol ürün kodlarını inceleyebilir; teknik uygunluk, alternatif ürün ve teklif desteği için Teknoais ekibiyle iletişime geçebilirsiniz.

ÜRÜN KODLARI

Raziol ürün kodları ve modelleri

Teknik değerlendirme ve teklif için 12 ürün kodu listeleniyor.

12kayıt

Ürün kodu

1012100150

RB F 0150 Roller lubricator standard felt ø 60 mm Low-wear felt rollers ø60 mm. The felt rollers are supplied with oil from the inside out through fixed hollow axles, Roll adjustment by tension springs, Min.recommended belt width: approx. 80 mm max.greasing width: 150 mm, Permissible oil viscosity (40 ° C): approx. 150 mm² / s With oil connection hoses and optical Feed control (dropper chambers), Model TK 2.

Ürün detayını incele

Ürün kodu

1012180300

RB 300 FK-P SW Roller oiler Kipp Pneumatic felt ø 60 with the following properties: - Oil mist-free lubricant application through low-wear felt rollers - The oil supply to the felt rollers is done from the inside by fixed hollow axles. - The adjustment of the upper roller to the material is done by Pneumatic cylinder, stroke height approx. 10 mm, with swivel device - Roller set change without tools - Oil connection on both sides of the upper and lower roller Technical data: - greasing rollers Ø 60 mm - Maximum recommended material thickness: approx. 5.0 mm - Maximum recommended oil viscosity (40°C): approx. 150 mm²/s - The oil must not be resinous and must not contain any solids. Dimensions: - Length in DLR: approx. 100 mm - Width across the DLR: approx. 555 mm (incl. space for oil connection) - Passline: 80 mm The scope of delivery of the roller oiler includes oil connection hoses with optical inflow control (dropper chambers TK4) including four quick-connector sockets. With built-in roller change kit: RB 300 FK-P SW. Roller oiler Kipp Pneumatic felt Ø 60 with the following properties: Oil mist-free lubricant application through low-wear felt rollers. The oil supply to the felt rollers is done from the inside by fixed hollow axles. The adjustment of the upper roller to the material is done by Pneumatic cylinder, stroke height approx. 10 mm, with swivel device. Roller set change without tools. Oil connection on both sides of the upper and lower roller. Technical data: greasing rollers Ø 60 mm, Maximum recommended material thickness: approx. 5.0 mm, Maximum recommended oil viscosity (40°C): approx. 150 mm²/s. The oil must not be resinous and must not contain any solids. Dimensions: Length in DLR: approx. 100 mm, Width across the DLR: approx. 555 mm (incl. space for oil connection). Passline: 80 mm. The scope of delivery of the roller oiler includes oil connection hoses with optical inflow control (dropper chambers TK4) including four quick-connector sockets. With built-in roller change kit:

Ürün detayını incele

Ürün kodu

1040940219

Funnel with check valve for manual filling of pressure storage tanks Consisting of: 1 x check valve 1" with connection fittings 1 x funnel Ø 160 mm, capacity 1.2 L For mounting on pressure tanks Funnel with check valve for manual filling of pressure storage tanks. Consisting of: 1 x check valve 1" with connection fittings, 1 x funnel Ø 160 mm, capacity 1.2 L. For mounting on pressure tanks

Ürün detayını incele

Ürün kodu

1042110012

Dos MST 010D-SS VBMV-2 opener Dosing system for customer-side control Consisting of: 1 x pressure reservoir with 10 L capacity and compressed air fitting up to 2.5 bar 1 x float switch, switching type "opener" 1 x filter 1/4" with ball valve 1 x oil distribution block VBMV-2, NW 1.0 mm with two Solenoid (24V DC) and two throttle valves. FOR WALL MOUNTING

Ürün detayını incele

Ürün kodu

1044111300

Oil distributor block VBMV-2 with two magnetic valves (but without throttles) on mounting plate for separate pressure reservoir. Complete with 2 solenoid coils 24V DC, oil connection for hose 10x3.5 and screw connections for hose PU-8/6, incl. hose NBR / PVC 10x3.5 (Aø17 / Iø10), assembled to 5 m

Ürün detayını incele

Ürün kodu

1045911111

HST hand lever up to 2.5 bar HIFT CONTROL HAND-OPERATED For starting and stopping the upper grease roller (e.g. when threading the tape) With pressure reducer and manometer up to 2.5 bar and connections for PU-AIR hose 4/2.3

Ürün detayını incele

Ürün kodu

1080040004-

TK 4 2 dripper chambers with PVC-8/5 tubing Optical feed control for connection to roller belt oilers with a Grease application width >300 mm consisting of: - 2 drip chambers - 2 x 1.5 m PVC-8/5 hoses and 4 x 1.5 m PVC-8/5 hoses - 2 Y-connectors

Ürün detayını incele

Ürün kodu